ATIKA SWINGLINE 2000 - Instruções de Operação descarregar pdf (Página 12)

Take note of the following instructions

to protect yourself and others from

hazards and injuries.

• Observe local accident prevention and safety

regulations in the work area.

• The operator is responsible for third parties in

the work area.

• Keep children away from machine.

• Persons younger than 16 years of age are not

allowed to operate the machine.

• Be sure that there is enough light.

• All dangerous parts have been covered with

safeguards for your protection. Do not modify

or remove the safeguards.

• Never modify the machine or parts thereof.

• Only start up the machine if the protective

devices are complete and undamaged.

• Always fix tightly tilting angle control during

storage, transport and operation.

• Faulty or damaged parts in the device must

be replaced immediately.

• Set up and run the machine on a solid, level

base only (where it will not tip over).

• Make sure that there is no danger of tripping

near the machine.

• Only use the machine for the functions listed in

"Proper use".

• Wear protective goggles and eye protection

while working with the machine.

• Do not spray machine with water (this is

hazardous due to live components).

• Do not leave the machine standing in the rain

or use when raining. Store the machine in a

dry place.

• Be absolutely sure to

pull the plug before:

- adjust the angle

- moving or transport

- cleaning, maintenance or repair work

Electrical safety

• Connecting attachments must be designed in

conformance with IEC 245-4:1980

(DIN 57 282) and marked H 07 RN-F, or

comparable models. Cross section of wires at

least 3 x 1.5 mm² up to a maximum length of

50 m. Wire cross-section at least 2.5 mm² for

lengths of more than 50 m.

• Use only connecting attachments with a

rubber plug device that is protected against

spraying water

• Check connecting attachments for defects or

ageing before using them.

• Never use defective connecting attachments.

• When laying the connecting attachments, be

sure that they do get crushed or bent, and that

the plug-and-socket connection does not get

wet.

• Do not use any provisional electrical

connections.

• Never bridge over protective devices or put

them out of operation.

• Connect the machine using a fault current

protection switch.

A licensed professional electrician must

make all electrical connections and repairs,

and observe local regulations in doing so,

especially those regarding protective measures.

The manufacturer or a company designated by

the manufacturer must attend to the repair of all

electrical parts on the machine.

Observe all safety instructions.

• Check that the machine is completely and

correctly assembled.

• Set the machine on a solid, level base.

• Connect the machine to an appropriate and

correctly wired electric socket.

• Only use extension leads with sufficient dia-

meters:

- cable up to 50 metres: diameter at least

1,5 mm².

- cable over 50 metres: diameter at least

2,5 mm².

• Fuse protection: 10 A

• Before using the machine, make sure each

time that

- there are no faulty connections

- all screws are tight

- whether tilting angle control is properly

tightened.

Switching on and off

! red  0 = OFF

green  = ON

! Switch the motor on and off only at the switch.

! In the event of a power failure, the machine will

switch off automatically. Press the switch

again to restart the machine.

Motor protection

The motor is equipped with a thermostat. The

thermostat switches the motor off automatically in

the event of overload (overheating). The machine

can be restarted after a cooling-off period.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 25 26

Comentários a estes Manuais

Sem comentários

ATIKA SWINGLINE 2000 - Instruções de Operação Página 12

Comentários a estes Manuais

Manuais e produtos relacionados com não ATIKA SWINGLINE 2000 -